Till sidans innehåll
🥁 Up to 70% off: Easter deals sweeter than chocolate! Shop now

K&M Twist Grip for Mic Stands

123

Clamping sleeve

  • For mic stands
  • Suitable for 210/2, 201 A / 2, 260/1, 260
  • Colour: Black
Tillgänglig sedan Maj 2004
Artikelnummer 170520
försäljningsenhet 1 Styck
Type Grip
fitted for Microphone Stand
20,30 kr
Alla priser inklusive moms
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
1

123 Kundbetyg

4.6 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

41 Recensioner

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
r
I'm sure these are fine.
ronhow 09.04.2018
I took gamble that these would fit my Millennium mic stands but they didn't. Nevertheless, the K&M parts are up to their normal high standard ... I think! Thomann told me they wouldn't fit but they looked the same and I didn't listen! Ha ha it was worth a punt as there are no replacement parts for the Millennium mic stands! I also replaced the booms with Millennium ones and they are solid and standing up to the rigours of live stage set up!
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
TS
Doesn't fit
Todd Sloan-Fortune 08.03.2014
I bought this as a bit of a gamble, hoping I could get it to fit on a Millennium MS-2003 microphone stand that I received with a broken twist grip from Thomann (they have replaced it quickly and efficiently). I wasn't expecting it to fit, but I was hoping that it would. It seems like it should be a fairly standard part that is replaceable, but clearly I was mistaken. I have no particular issues with the part, but I can't really be used as a true critic for the item as I haven't managed to get to use it properly.
hantverkskvalitet
1
1
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
AG
Twist Grip for K&M Mic stands
Andrey Gurskiy 05.11.2024
We had at our church some old K&M mic stands which were not possible to use at all. The stand could not hold the height because the twist grips had been broken.
I ordered these original K&M Twist Grips )which looks a little bit differently but fit to my K&M stands) and replace at two of our mic stands.
And they became like a brand new. After replacement we had been using them after repair already 3 years without any issues!
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate de
Tyvärr uppstod ett fel. försök igen senare.
S
Toll, dass es das als Ersatzteil gibt
Soul-Café 13.07.2016
Wie in der Überschrift schon steht, bin ich froh, dass es dieses Teil als Ersatzteil gibt. Bei uns im Schulbetrieb ging der kleine "Kunststoffring" irgendwie verloren (keine Ahnung wie aber Schüler haben da wohl einen Spieltrieb und legen alles auseinander und beim Zusammen setzen ist da wohl was verloren gegangen). Dadurch konnte ich einen der Ständer nicht mehr nutzen.
Mit diesem Ersatzteil, der sich leicht einbauen lässt ist der Ständer für wenig Geld wieder voll Funktionsfähig.

Einbau: Drehgriff ganz abschrauben, dünnere Stange ganz rausziehen, evtl. noch Rändelschaube von dünnerer Stange abschrauben, kleinen Kunststoffring auf dünnere Stange mit Verdünnung nach unten aufstecken, dünne Stange in "Standrohr" einführen, Drehgriff von oben wieder festschrauben, evtl. Rändelschraube wieder aufschrauben. fertig. Das hört sich jetzt viel an ist aber in 1-2 Min erledigt.

Das Teil ist auch sinnvoll, wenn de Drehgriff (Feststellgriff) durch zu festes Anziehen bricht.

Der Preis ist dafür ist auch OK.
hantverkskvalitet
2
0
Anmäl recension

Anmäl recension